If your tube amp has suddenly began to crackle, you’re likely to find yourself getting frustrated very quickly. Many different things can cause this annoying issue, and isolating the problem can prove difficult. Luckily, this guide will help take you through the possibilities step-by-step so you can figure out what’s causing the crackling (and how to stop it).
Whenever you’re dealing with a tube amp of any kind, it’s very important that you take precautions to avoid being burned by hot tubes or even electrocuted. Be very careful when working inside your tube amp. Where eye protection and consider heat-resistant gloves to keep you safe. You should also be certain that you know what you’re doing. Aiken Amps has a good list of tube amp safety tips here.
If your confidence levels are low (or far too high), you should consider reaching out to an expert to assist you in figuring out the source of the problem and implementing a solution. It’s not worth getting injured, or even killed, to save a few bucks. Tube amps are not something you should be “tinkering” with if you are unfamiliar with the things you are handling.
When in doubt, wait it out and call in an expert to lend a hand.
Study The Issue
The first step in solving the problem you’re facing is to study the issue in itself by asking some questions about the noise and when it occurs.
Does the crackling get louder as you turn up the amp? Most often, it will stay the same volume regardless of how loud you turn up the volume knobs. The crackling may be an occasional pop and crack or a steady droning. Studying the issue and when/how it’s occurring can help you narrow down the potential causes.
Is the crackling coming through all your speakers or just one channel? This is another question you should be considering as you go forward to find the cause and solution.
It’s also good to clarify that this article is going to look at crackling that’s coming through your amp’s speakers. If you’re just worried about crackling coming from the tubes themselves when you turn on/off the amp, this is usually just a normal sign that they are warming up and changing temperature (typically not a problem that needs addressing).
However, if the crackling is coming through your speakers, let’s look into some potential causes and solutions.
The Quick Fixes
Troubleshoot your problem by first turning down any internal effects your amp has, like tremolo or reverb. Turn down all your volume controls as well. Next, hit the top of the amp with moderate force (yes, seriously!).
If the sound occurs, study it and try the first response solutions described below. If the sound does not occur, try turning up the volume controls to the settings you normally have them at and then try this method again. If it does not occur, the below quick fixes are worth trying anyways before getting more in-depth into the matter.
- Rumbling: If the sound is very rumbly, your amp may have a faulty output tube. You’ll want to replace your amp’s power tubes using a complete set of matched spares. If the problem continues, put back the original tubes and continue troubleshooting.
- Glassy / High-Pitched: You likely have a faulty preamp tube. Begin by working your way across from the preamp tubes closest to the output tubes. Tap each tube with a pencil. If one produces the noise, replace it. This may fix the problem. Otherwise, continue the process and replace any other preamp tubes that cause the sound. This can also be used for an output tube that’s potentially causing the issue.
- Loud and static-like: Check all of your amp’s connections! Check your speaker/input cables and your tube sockets and clean them thoroughly. A dirty, oxidized, or compromised connection anywhere inside your amp will cause static-y sounds.
- Random crackles and pops: Your amp likely has faulty power tubes or preamp tubes. Try swapping them one-by-one with spares or have them replaced in full. If replacing your tubes does not fix the problem, you need to have a qualified tech check your preamp’s plate or cathode resistor.
Need more information? Read on for some more in-depth advice in case the above quick fixes haven’t worked for you yet.
Clean Your Connections
First and foremost, check all connecting cables to your tube amps and clean them thoroughly. A dirty connector is the most common cause of crackling sounds in tube amps.
Unfortunately, the cause isn’t always this simple, but give it a shot anyway. Even if your connectors aren’t that old, a poor quality connector can give you problems anyway. Once cleaned, plug your connectors back in and see if the problem persists. If it does, try swapping out your connectors to see if the connector is the source of the problem.
Ampmechanic.com has a guide to cleaning your amplifier here.
When you have ruled out your connectors, move forward with these other potential solutions.
Check Your Power
There may be interference with your power source. To check, isolate your amp’s power to a different circuit (not just a different outlet) and see if the problem persists. If it does, there is something within your home’s power grid interfering with your amp.
Hopefully you’ll be able to use the new and unaffected circuit from here on out. Otherwise, your solution is going to have to figure out the issue with your circuit so you can fix it and move the amp back to its original plug.
Look At Your Tubes
A poor tube connection may be the source of the crackling noise you’re hearing. Sometimes, gently pulling on the tubes can help re-seat them better and give them a better connection, thus fixing your problem.
The crackling can also be caused by a bad tube, in which case you’ll need to try swapping them out. Hopefully you have some spares on hand for testing purposes! Occasionally, you may also find that swapping the position of your current tubes can fix the crackling (which usually means it’s a connection issue).
Generally, if your crackling occurs at random, you should be looking at your tubes. Same goes for crackling or popping that sounds out when you aren’t even playing anything through your amp.
Go through one by one and replace each of your preamp tubes to see if this stops the crackling from occurring. This can take a lot more time to test out thoroughly if the crackling happens at random. You may have to swap one tube and wait hours (or even days) to see if the crackling happens again.
If you go through all of your tubes and they don’t seem to be the cause of the crackling, get a set of matched spares and replace all of your output tubes.
If none of these solutions have worked for your amp, it’s probably time you take it into a qualified technician as the problem is likely a failing plate or cathode resister inside of your preamp.
Other Common Problems
If you are running into one of these other common tube amp problems, it’s worth having a look into this brief solutions:
- Sound Cutting Out: If your tube amp’s sound is cutting in and out while you use it, the first thing to check is your tube sockets (see above). You should also check the connections and clean them thoroughly (this means spraying electronic cleaner into the jack, cleaning the ends of cables, and then plugging them in/out about 10 times).
- No Sound At All: If your tube amp has gone silent, it’s worth checking your speaker. An open speaker connection should be the first potential culprit you consider when your amp has gone silent.
If you’re still experiencing problems after trying these proposed solutions, it’s worth taking your amp to an expert and using this as an opportunity to learn.
Want more? Sweetwater.com has a great resource here and Premier Guitar has a nice article on “amp first aid” here.
lisa gerrard says
i have an Audio Note valve stereo, I have spent money on fixing the crackling problem, it is like a breath pulsating, i cant seem to get to the bottom of the problem, I have a power conditioner so i don’t believe its is this, If you have any advise I would very much appreciate your opinions,